Pontiac Car Forums


Reply
Thread Tools Display Modes

2001 Pontiac Montana Key FOB programming

 
kissrawks
Guest
Posts: n/a
 
      03-18-2005
How do I program a Key Fob for a 2001 Pontiac Montana ?

Thanks



--
Posted using the http://www.autoforumz.com interface, at author's request
Articles individually checked for conformance to usenet standards
Topic URL: http://www.autoforumz.com/Pontiac-20...ict108028.html
Visit Topic URL to contact author (reg. req'd). Report abuse: http://www.autoforumz.com/eform.php?p=504500
 
Reply With Quote
 
 
 
 
DonW
Guest
Posts: n/a
 
      03-18-2005

"kissrawks" <(E-Mail Removed)> wrote in message
news:1_504500_0f381e80cd6aa9eaa541ff26cedf576d@aut oforumz.com...
> How do I program a Key Fob for a 2001 Pontiac Montana ?
>
> Thanks
>
>
>
> --
> Posted using the http://www.autoforumz.com interface, at author's request
> Articles individually checked for conformance to usenet standards
> Topic URL:
> http://www.autoforumz.com/Pontiac-20...ict108028.html
> Visit Topic URL to contact author (reg. req'd). Report abuse:
> http://www.autoforumz.com/eform.php?p=504500


The following was taken from the Service Information for a 01 Montana. I
can not verify it will work:

Transmitter Programming

Important
All transmitters which are to be recognized by the remote control door lock
transmitter (RCDLR) must be programmed in a single programming sequence. If
the system is placed in program mode it will erase all previously programmed
transmitters upon the receipt of the programming signal from the first
transmitter. Up to four transmitters can be programmed. Do not operate or
program the transmitters in the vicinity of other vehicles that are in the
keyless entry program mode. This prevents the programming of the
transmitters to the incorrect vehicle.

1. Remove the ignition key from the ignition lock cylinder.
2. Remove the BCM PRGRM fuse from the fuse block.
3. Close all of the doors.
4. Insert the ignition key into the ignition lock cylinder.
5. Turn the ignition to ACC. The body control module (BCM) will perform the
following in order to identify the type of BCM installed in the vehicle:
Flash the seat belt indicator 2, 3, or 4 times.
Chime 2, 3, or 4 times.
6. Turn the ignition to OFF, and then back to ACC within 1 second. The BCM
may begin to chime and flash diagnostic trouble codes (DTCs). If the BCM has
stored any DTCs, refer to Diagnostic System Check - Body Control System in
Body Control System.
7. Open and then close any vehicle door. The BCM will chime in order to
confirm that the programming mode has been entered.
8. Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for
approximately 14 seconds.

Important
After approximately 3-5 seconds the BCM will chime once to confirm that the
programming has been completed for that transmitter.
9. Repeat the previous step in order to program each additional
transmitter.
10. Remove the ignition key from the ignition lock cylinder.
11. Install the BCM PRGRM fuse into the fuse block.
12. Operate the functions of each transmitter in order to verify correct
system operation.


 
Reply With Quote
 
 
 
 
kissrawks
Guest
Posts: n/a
 
      03-21-2005
"DonW" wrote:
> "kissrawks" <(E-Mail Removed)> wrote in message
> news:1_504500_0f381e80cd6aa9eaa541ff26cedf576d@aut oforumz.com...
> > How do I program a Key Fob for a 2001 Pontiac Montana ?
> >
> > Thanks
> >
> >
> >
> > --
> > Posted using the http://www.autoforumz.com interface, at author's request
> > Articles individually checked for conformance to usenet

> standards
> > Topic URL:
> > http://www.autoforumz.com/Pontiac-20...ict108028.html
> > Visit Topic URL to contact author (reg. req'd). Report

> abuse:
> > http://www.autoforumz.com/eform.php?p=504500

>
> The following was taken from the Service Information for a 01
> Montana. I
> can not verify it will work:
>
> Transmitter Programming
>
> Important
> All transmitters which are to be recognized by the remote
> control door lock
> transmitter (RCDLR) must be programmed in a single programming
> sequence. If
> the system is placed in program mode it will erase all
> previously programmed
> transmitters upon the receipt of the programming signal from
> the first
> transmitter. Up to four transmitters can be programmed. Do not
> operate or
> program the transmitters in the vicinity of other vehicles
> that are in the
> keyless entry program mode. This prevents the programming of
> the
> transmitters to the incorrect vehicle.
>
> 1. Remove the ignition key from the ignition lock cylinder.
> 2. Remove the BCM PRGRM fuse from the fuse block.
> 3. Close all of the doors.
> 4. Insert the ignition key into the ignition lock cylinder.
> 5. Turn the ignition to ACC. The body control module (BCM)
> will perform the
> following in order to identify the type of BCM installed in
> the vehicle:
> Flash the seat belt indicator 2, 3, or 4 times.
> Chime 2, 3, or 4 times.
> 6. Turn the ignition to OFF, and then back to ACC within 1
> second. The BCM
> may begin to chime and flash diagnostic trouble codes (DTCs).
> If the BCM has
> stored any DTCs, refer to Diagnostic System Check - Body
> Control System in
> Body Control System.
> 7. Open and then close any vehicle door. The BCM will chime in
> order to
> confirm that the programming mode has been entered.
> 8. Press and hold the transmitter LOCK and UNLOCK buttons
> simultaneously for
> approximately 14 seconds.
>
> Important
> After approximately 3-5 seconds the BCM will chime once to
> confirm that the
> programming has been completed for that transmitter.
> 9. Repeat the previous step in order to program each
> additional
> transmitter.
> 10. Remove the ignition key from the ignition lock cylinder.
> 11. Install the BCM PRGRM fuse into the fuse block.
> 12. Operate the functions of each transmitter in order to
> verify correct
> system operation.


Thank you, this worked great without a problem!
 
Reply With Quote
 
 
 
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
2001 Pontiac Montana - AC Not working - blows hot air ChallengeAndInspire@gmail.com Pontiac Montana 2 06-02-2007 02:32 AM
2001 Pontiac Montana, lost AC and now smell coolant. Mike Pontiac Montana 1 08-29-2004 05:45 PM
Keyless Remote programming for 1998 Transport Montana josh Pontiac Montana 1 06-25-2004 01:10 AM
Pontiac 2001 Montana - Changing Fog Lamps easyville Pontiac Montana 0 02-29-2004 02:26 PM
Oil Light Reset on 2001 Pontiac Montana Trashbox Pontiac Montana 0 07-10-2003 12:02 AM


All times are GMT. The time now is 06:07 PM.